HtrA Serine Peptidase 1 (HTRA1) ELISA Kit

Details for Product No. ABIN1081533, Supplier: Log in to see
Antigen
  • htra1
  • zgc:92029
  • zgc:172061
  • l56
  • htra
  • Xhtra1
  • prss11
  • MGC145723
  • ARMD7
  • CARASIL
  • HtrA
  • L56
  • ORF480
  • PRSS11
  • AI429470
  • HTRA
  • Prss11
  • RSPP11
  • HTRA1
  • HtrA serine peptidase 1a
  • HtrA serine peptidase 1
  • HtrA serine peptidase 1b
  • Serine protease HTRA1
  • serine protease
  • htra1a
  • HTRA1
  • htra1b
  • htra1
  • Htra1
  • HTRA
Alternatives
Human HtrA Serine Peptidase 1 ELISA Kit
Reactivity
Human
Alternatives
Kits with alternative reactivity to:
22
2
1
1
1
1
Method Type
Sandwich ELISA
Detection Range
8.23-6.000 pg/mL
Minimum Detection Limit
8.23 pg/mL
Application
ELISA
Options
Supplier
Log in to see
Supplier Product No.
Log in to see
Purpose The Chemiluminescent Immunoassay kit is designed for the in vitro sensitive quantitative measurement of HTRA1 in human serum, plasma and other biological fluids.
Sample Type Serum, Plasma, Biological Fluids
Analytical Method Quantitative
Detection Method Chemiluminescent
Specificity

This assay has high sensitivity and excellent specificity for detection of High Temperature Requirement Factor A1 (HTRA1).
No significant cross-reactivity or interference between High Temperature Requirement Factor A1 (HTRA1) and analogues was observed.

Cross-Reactivity (Details) No significant cross-reactivity or interference between HtrA Serine Peptidase 1 (HTRA1) and analogues was observed.
Sensitivity 2.99 pg/mL
Components
  • Pre-coated, ready to use 96-well strip plate
  • Plate sealer for 96 wells
  • Standard Diluent
  • Assay Diluent A
  • Assay Diluent B
  • Stop Solution
  • Standard
  • Detection Reagent A
  • Detection Reagent B
  • TMB Substrate
  • Wash Buffer (30 × concentrate)
  • Instruction manual
Material not included
  • Luminometer capable of reading 96-well microplates with the following parameters: lag time 30.0 secs, read time 1.0 sec/well .
  • Precision single or multi-channel pipettes and pipette tips with disposable tips.
  • Eppendorf Tubes for diluting samples.
  • Deionized or distilled water.
  • Absorbent paper for blotting the microtiter plate.
  • Container for Wash Solution
Alternative Name HTRA1 (HTRA1 ELISA Kit Abstract)
UniProt Q92743
Pathways Growth Factor Binding
Application Notes
  • Limited by the current condition and scientific technology, we cannot completely conduct the comprehensive identification and analysis on the raw material provided by suppliers. So there might be some qualitative and technical risks to use the kit.
  • The final experimental results will be closely related to validity of the products, operation skills of the end users and the experimental environments. Please make sure that sufficient samples are available.
  • Kits from different batches may be a little different in detection range, sensitivity and color developing time.
  • Do not mix or substitute reagents from one kit lot to another. Use only the reagents supplied by manufacturer.
  • Protect all reagents from strong light during storage and incubation. All the bottle caps of reagents should be covered tightly to prevent the evaporation and contamination of microorganism.
  • There may be some foggy substance in the wells when the plate is opened at the first time. It will not have any effect on the final assay results. Do not remove microtiter plate from the storage bag until needed.
  • Wrong operations during the reagents preparation and loading, as well as incorrect parameter setting for the plate reader may lead to incorrect results. A microplate plate reader with a bandwidth of 10nm or less and an optical density range of 0-3 O.D. or greater at 450 ± 10nm wavelength is acceptable for use in absorbance measurement. Please read the instruction carefully and adjust the instrument prior to the experiment.
  • Even the same operator might get different results in two separate experiments. In order to get better reproducible results, the operation of every step in the assay should be controlled. Furthermore, a preliminary experiment before assay for each batch is recommended.
  • Each kit has been strictly passed Q.C test. However, results from end users might be inconsistent with our in-house data due to some unexpected transportation conditions or different lab equipments. Intra-assay variance among kits from different batches might arise from above factors, too.
  • Kits from different manufacturers for the same item might produce different results, since we have not compared our products with other manufacturers.
Comment

Information on standard material:
The standard might be recombinant protein or natural protein, that will depend on the specific kit. Moreover, the expression system is E.coli or yeast or mammal cell. There is 0.05% proclin 300 in the standard as preservative.

Information on reagents:
The stop solution used in the kit is sulfuric acid with concentration of 1 mol/L. And the wash solution is TBS. The standard diluent contains 0.02 % sodium azide, assay diluent A and assay diluent B contain 0.01% sodium azide. Some kits can contain is BSA in them.

Information on antibodies:
The provided antibodies and their host vary in different kits.

Sample Volume 100 μL
Assay Time 3 h
Plate Pre-coated
Protocol The microplate provided in this kit has been pre-coated with an antibody specific to High Temperature Requirement Factor A1 (HTRA1). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to High Temperature Requirement Factor A1 (HTRA1). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the High Temperature Requirement Factor A1 (HTRA1) level in the sample or standard.,
Reagent Preparation
  • Bring all kit components and samples to room temperature (18-25°C) before use.
  • Standard - Reconstitute the Standard with 1.0mL of Standard Diluent, kept for 10 minutes at room temperature, shake gently(not to foam). The concentration of the standard in the stock solution is 12,000pg/mL. Please firstly dilute the stock solution to 6,000pg/mL and the diluted standard serves as the highest standard (6,000pg/mL). Then prepare 7 tubes containing 0.6mL Standard Diluent and use the diluted standard to produce a triple dilution series. Mix each tube thoroughly before the next transfer. Set up 7 points of diluted standard such as 6,000pg/mL, 2,000pg/mL, 666.7pg/mL, 222.2pg/mL, 74.1pg/mL, 24.7pg/mL, 8.2pg/mL, and the last EP tubes with Standard Diluent is the blank as 0pg/mL.
  • Assay Diluent A and Assay Diluent B - Dilute 6mL of Assay Diluent A or B Concentrate(2×) with 6mL of deionized or distilled water to prepare 12 mL of Assay Diluent A or B. (In fact, more than 6mL Assay Diluent A and Assay Diluent B are contained in the bottles. Therefore, in every test, please precisely pipette required amount of Diluent and make double dilution in a new container. The prepared working dilution cannot be frozen.)
  • Detection Reagent A and Detection Reagent B - Briefly spin or centrifuge the stock Detection A and Detection B before use. Dilute to the working concentration with working Assay Diluent A or B, respectively (1:100).
  • Wash Solution - Dilute 20mL of Wash Solution concentrate (30×) with 580mL of deionized or distilled water to prepare 600 mL of Wash Solution (1×).
  • Substrate working Solution - Mix the substrate A and B by the ratio of 99:1 to make the substrate working solution. Mix thoroughly. For example, prepare 1,000µL Substrate working Solution with 990µL Substrate A + 10µL Substrate B.
Note:
  • Making serial dilution in the wells directly is not permitted.
  • Prepare standard within 15 minutes before assay. Please do not dissolve the reagents at 37°C directly.
  • Please carefully reconstitute Standards or working Detection Reagent A and B according to the instruction, and avoid foaming and mix gently until the crystals are completely dissolved. To minimize imprecision caused by pipetting, use small volumes and ensure that pipettors are calibrated. It is recommended to suck more than 10µL for once pipetting.
  • The reconstituted Standards, Detection Reagent A and Detection Reagent B can be used only once.
  • Prepare Substrate working Solution within 15 minutes before assay.
  • If crystals have formed in the Wash Solution concentrate (30×), warm to room temperature and mix gently until the crystals are completely dissolved.
  • Contaminated water or container for reagent preparation will influence the detection result.
Sample Collection Serum: Allow samples to clot for two hours at room temperature or overnight at 4°C before centrifugation for 20 minutes at approximately 1000 × g. Assay immediately or store samples in aliquot at -20°C or -80°C. Avoid repeated freeze/thaw cycles.

Plasma: Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 15 minutes at 1000 × g within 30 minutes of collection. Remove plasma and assay immediately or store samples in aliquot at -20°C or -80°C. Avoid repeated freeze/thaw cycles.

Biological Fluids: Centrifuge samples for 20 minutes at 1000 × g. Remove particulates and assay immediately or store samples in aliquot at -20 °C or -80 °C for later use. Avoid repeated freeze/thaw cycles.
Sample Preparation
  • We are only responsible for the kit itself, but not for the samples consumed during the assay. The user should calculate the possible amount of the samples used in the whole test. Please reserve sufficient samples in advance.
  • Please predict the concentration before assaying. If values for these are not within the range of the standard curve, users must determine the optimal sample dilutions for their particular experiments. Sample should be diluted by 0.01mol/L PBS(PH=7.0-7.2).
  • If the samples are not indicated in the manual, a preliminary experiment to determine the validity of the kit is necessary.
  • Tissue or cell extraction samples prepared by chemical lysis buffer may cause unexpected ELISA results due to the impacts from certain chemicals.
  • Due to the possibility of mismatching between antigen from other origin and antibody used in our kits (e.g.antibody targets conformational epitope rather than linear epitope), some native or recombinant proteins from other manufacturers may not be recognized by our products.
  • Influenced by the factors including cell viability, cell number or sampling time, samples from cell culture supernatant may not be detected by the kit.
  • Fresh samples without long time storage is recommended for the test. Otherwise, protein degradation and denaturalization may occur in those samples and finally lead to wrong results.
Assay Procedure
  1. Prepare all reagents, samples and standards,
  2. Add 100μL standard or sample to each well. Incubate 2 hours at 37 °C,
  3. Aspirate and add 100μL prepared Detection Reagent A. Incubate 1 hour at 37 °C,
  4. Aspirate and wash 3 times,
  5. Add 100μL prepared Detection Reagent B. Incubate 30 minutes at 37 °C,
  6. Aspirate and wash 5 times,
  7. Add 100μL Substrate Solution. Incubate 10 minutes at 37 °C,
  8. Read RLU value immediately.
Calculation of Results

Average the duplicate readings for each standard, control, and samples and subtract the average zero standard relative light unit (RLU). Create a standard curve on log-log graph paper, with HTRA1 concentration on the y-axis and the RLU value on the x-axis. Draw the best fit straight line through the standard points and it can be determined by regression analysis. Using some plot software, such as curve expert 1.30, is also recommended. If samples have been diluted, the concentration read from the standard curve must be multiplied by the dilution factor.
In order to make the calculation easier, we plot the RLU value of the standard (X-axis) against the known concentration of the standard (Y-axis), although concentration is indeed the independent variable while RLU value is the dependent variable. Further, in this part, in order to help the customer perform the assay more visual, we provide the customer with the raw data (not the log of data). However, plotting log of the data to construct the curve will be recommended. The RLU values of the standard curve may vary according to the conditions of assay performance (e.g. operator, pipetting technique, washing technique or temperature effects). This curve is provided for demonstration only. The customers should establish their own standard curve for each test conducted.

Assay Precision

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level High Temperature Requirement Factor A1 (HTRA1) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level High Temperature Requirement Factor A1 (HTRA1) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Restrictions For Research Use only
Precaution of Use The Stop Solution suggested for use with this kit is an acid solution. Wear eye, hand, face, and clothing protection when using this material.
Handling Advice

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5 % within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Storage 4 °C
Storage Comment
  • For unopened kit: All the reagents should be kept according to the labels on vials. The Standard, Detection Reagent A, Detection Reagent B and the 96-well strip plate should be stored at -20°C upon receipt while the others should be at 4°C.
  • For opened kit: When the kit is opened, the remaining reagents still need to be stored according to the above storage condition. Besides, please return the unused wells to the foil pouch containing the desiccant pack, and reseal along entire edge of zip-seal.
    Note: It is highly recommended to use the remaining reagents within 1 month provided this is within the expiration date of the kit.
  • For ELISA kit, 1 day storage at 37°C can be considered as 2 months at 4°C, which means 3 days at 37°C equaling 6 months at 4°C.
Expiry Date 6 months
Supplier Images
ELISA image for HtrA Serine Peptidase 1 (HTRA1) ELISA Kit (ABIN1081533) HtrA Serine Peptidase 1 (HTRA1) ELISA Kit
Did you look for something else?